coldpatch0

How to Replace a Kia Sportage Replacement Key The key in many Kia models comes with an electronic keyless entry system built in. The key functions like remote controls and can be exchanged with an Kia dealer. Key fobs may stop working due to a variety of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some suggestions to help you get your Kia key fob that is a replacement for the sportage again. How do you replace the remote key or smart key No matter if your Kia is equipped with an intelligent key, remote key push-to-start keys, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacing. This is especially when your car displays a message that indicates the smart or remote keys have low battery power. Luckily, it's quite simple to do. In order to replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob and lift the cover. Inside the key fob will be the small screw that holds the battery in the correct position. Remove kia replacement key by removing the screw using the help of a small screwdriver. Install the new battery and close the cut on the key fob. Test the key fob by pressing the lock/unlock buttons. It's okay when the doors lock or unlock as you expect. You can now use Kia's hands-free lock/unlock function whenever your fingers feel cold or you have to go on errands around Brandon. Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a machine for programming that is only available to the automotive locksmith or dealer. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, you'll need write down the key code's number on the tag for the key code. How do you replace a dead battery? If the Kia key fob doesn't respond when you press the lock/unlock button, it's a sign that the battery is depleted. A low battery can also cause other issues, like the check engine light flashing or the engine not cranking properly. It is fairly easy to replace key fob batteries with only the use of a few tools. Before you begin the process before beginning the process, ensure that your vehicle is turned off and that all doors are shut. Find the small, metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the key is released. Then, you can put the key into the handle on the door of your driver to unlock your car. To replace the key fob's battery, take off the cover at the rear and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery and align the new battery in a way that the “+” positive side faces you, while the “–” negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the contacts of the metal. After installing the new battery after which you turn the key fob off and on in the ignition until the door locks up. You can then test your Kia key fob to determine if it is working properly again. How do you replace a keyless key You could have the standard keyfob or Smart Key based upon the model of Kia Sportage. The difference between these is that the smart fob has tiny mechanical key blade in it, whereas the standard fob isn't equipped with. Both kinds of key fobs come with a battery inside them that eventually will need to be replaced. It is a simple process that takes less than two minutes. Make sure you turn off your Kia, and be on a level and well-lit surface prior to you begin. Keep in mind that there are tiny parts inside the fob that could be removed if not vigilant. The first step is to locate the small release button that is located on the back of the lower part of the fob. It's either a circular or rectangular slot. You can open the key fob by pressing the button. Once the key fob is open, remove the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done it should be possible to lock and unlock your vehicle with your key fob even if your engine isn't running! How do you replace a mechanical key The Kia key fob is a wonderful convenience that lets us lock and unlock our vehicle with the click of one button. Like any other device there are issues with it at times. There are methods to troubleshoot these issues and keep our key fobs in good working order in the long run. One of the most common problems is a low or dead battery. This can cause your device to stop working or work intermittently. If this is the case, try replacing the battery with a new one. If this doesn't solve the issue Try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one. Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the key fob to confirm it's working properly. Contact a dealer locksmith to address the issue in the event that the fob is not working. To avoid locking outs in the future, ensure that you have an emergency key that will be able to work with all trunk and door cylinders.